主要蒸发

Devolatilization of solvents from viscous polymer cement is realized through stripping of solvent with steam in stirred vessels or directly by evaporating the solvent from the polymer. The later so-called direct desolventizing is realized in extruders or high volume kneaders. All 3 methods involve additional energy to drive out solvent either by partial pressure through additional steam (steam stripping), building and releasing pressure in order to explode the polymer bulk (extruder) or dynamic surface renewal (kneader).
Language: English / Year: 2005

Eine konzentrierte Elastomerlösung (weniger als 20 % Lösungsmittel) wird einem großvolumigen Knetreaktor zugeführt, um das Lösungsmittel bis auf ppm-Gehalte zu entfernen. Um diesen Entgasungsschritt zu beschreiben, wurde ein Simulationsprogramm entwickelt. Das Programm errechnet den Restlösungsmittelgehalt, den Füllgrad und das Drehmoment des Reaktors. Es kann sowohl der Feineinstellung sowie auch dem Scale-up des Prozesses dienen.
Language: German / Year: 2005

A concentrated rubber solution (less than 20 % solvent) is fed to a high volume kneader in order to remove the solvent down to ppm level. A simulation program has been developed to describe this devolatilization step. The program predicts final solvent content, the filling level and the mechanical torque build-up. The program can be used to refine process control and the scale-up of this type of process.
Language: English / Year 2005

The achievable final volatile content within kneader devolatilization processes is highly dependent on the final melt temperature. For thermosensitive polymers the state of the art process performs poorly. The amount of dissipated energy leads to a heat up of the polymer, limiting the maximal kneader shaft speed and therefore volatile removal rate. This new process uses a suitable additional volatile compound to cool off the dissipated energy by evaporation using the off gas to strip and boost the mass transfer coefficient. A complex multi-parameter study is presented, to predict performance of industrial equipment from pilot scale data.
Language: English / Year: 2011

For decades, conventional polymerisation has been the norm in the production of elastomers. The time and cost involved in removing and treating solvents in the final stages of production were acceptable. Yet as pressure builds on manufacturers to reduce operating costs, there is greater urgency to develop processes that can help streamline costs and production techniques. One such effort has yielded extremely promising results.
Language: English / Year: 2015

Conventional polymerisation in the production of elastomers has been the norm for decades. The time and cost involved in removing and treating solvents in th e final stages of production , for example, were acceptable, but as pressure builds on manufacturers to reduce operating costs, there is greater urgency to develop processes that can help streamline cost and production. One such effort has yielded extremely promising results.
Language: English / Year: 2013

For decades, conventional polymerization in the production of elastomers has been the norm. The time and cost involved in removing and treating solvents in the final stages of production, for example, were acceptable. But as pressure builds on manufacturers to reduce operating costs, there is greater urgency to develop processes that can help streamline cost and production. One such effort by List AG has yielded promising results.
Language: English / Year: 2014

Die bestehenden Technologien für die Aufbereitung von Polymeren nach der Polymerisation können in ein-, zwei- und mehrstufige Verfahren unterteilt werden. Dem entsprechend kommen Stripptechnologien mit nachgeschalteter mechanischer und thermischer Entfernung der Hilfsmittel, Extruder in verschiedenen Bauarten und großvolumige Kneter zum Einsatz. Die Knetertechnologie ist vor allem für temperatur- und scherempfindliche Polymermassen geeignet, bei denen die Entgasung diffusionsbestimmt ist.
Language: German / Year: 2006

The difference in the production of PA6 in comparison to that of other polymers is the downstream water extraction and drying after the granulation. During these process steps, the monomer and the oligomer contents in the final product are reduced in the 0.2 to 0.6 ww/w range. The installed units for extraction and drying of the final granulated product are characterized by their large energy consumption, which considerably influences manufacturing costs.
Language: English / Year: 2002

Synthetic elastomers have been produced for over 50 years. Advances in catalyst systems and polymer formulations have been somewhat diminished by the continued use of the same processing technology. In particular, the use of coagulation, steam stripping, mechanical dewatering, and convective drying for the devolatilization of temperature sensitive elastomeric solutions can be replaced with direct devolatilization using kneader technology. A two-step, direct devolatilization process has demonstrated energy savings and advantages in environmental emissions and process/product flexibility when compared to the conventional steam stripping process.
Language: English / Year: 2008

Der Einsatz von großen Lösemittelmengen in Polymerisationsprozessen mit den damit verbundenen Nachteilen muss nicht sein. Ein optimiertes Verfahren ermöglicht die direkte Entgasung von Lösemitteln, ohne dabei Strippmittel einsetzen zu müssen. Aufwendige Trennschritte werden so vermieden und höhere Produktqualitäten können erreicht werden.
Language: German / Year: 2010

Polymerprozesse – Aufbereitung und Finishing von Polymeren – Knetertechnologie in der Polymeraufbereitung – Wirtschaftlichkeit
Language: German / Year: 2006

Das Fraunhofer-Pilotanlagenzentrum für Polymersynthese und -verarbeitung
Language: German / Year: 2005

Energieeinsparung und Qualitätsverbesserung durch indirekte Eindampfung von Polymerlösungen oder direkte Polymerisation und Polykondensation
Language: German / Year: 2004

The achievable final volatile content within kneader devolatilization processes is highly dependent on the final melt temperature. For thermosensitive polymers the state of the art process performs poorly. The amount of dissipated energy leads to a heat up of the polymer, limiting the maximal kneader shaft speed and therefore volatile removal rate. This new process uses a suitable additional volatile compound to cool off the dissipated energy by evaporation using the off gas to strip and boost the mass transfer coefficient. A complex multi-parameter study is presented, to predict performance of industrial equipment from pilot scale data.
Language: English / Year: 2011

Die Synthese von Kautschuk ist ein wichtiger Prozess: Hersteller von Gummiprodukten – ganz gleich ob Autoreifen oder Kondome – benötigen hochwertigen Kautschuk als Ausgangswerkstoff. Doch die Kautschukerzeugung ist teuer und verschlingt große Mengen an Energie. Forschern des Fraunhofer-Instituts für Angewandte Polymerforschung IAP in Potsdam ist es gemeinsam mit ihren Entwicklungspartnern LIST AG und Dow Olefinverbund GmbH gelungen, den Energiebedarf der Kautschuksynthese um 76 Prozent zu senken.
Language: German / Year: 2007

Kneader reactors are used for combined unitary processing in the polymer industry for devolatilization, compounding or polymerization. In the past, mass transport prediction for devolatilization operations in kneader reactors did not match experimental results, when diffusion was assumed as sole driving force. It was detected that there is an additional concentration and temperature dependent driving force that triggers enhanced transport at finite solvent concentrations by orders of magnitude. The author suggests that the underlying root cause is likely micro bubble formation within the polymer melt. An attempt to model this additional mass transport mechanism is presented.
Language: English / Year: 2008

Der Einsatz von großen Lösungsmittelmengen in Polymerisationsprozessen mit den damit verbundenen Nachteilen muss nicht sein. Ein neues Verfahren beschreitet neue Wege: Kneten statt strippen lautet die Devise.
Language: German / Year: 2010

The synthesis of most elastomers is carried out either by Solution or emulsion polymerization. After the polymcrization step, the polymer is separated from the solvent or emulsifying agents. This separation requires several process steps including coagulation, Stripping, various mechanical separation stages, and finally diying. Beyond that, the existing technologies are energy consuming, waste solvent must be incinerated, and the installation of main and ancillaiy equipment occupies large spaces.
Lamguage: English / Year: 2007

Large volume kneaders are designed to handle highly viscous polymer processing. The unitary operations can be compounding, polymerizations, devolatilization or drying. Depending on the polymer viscosity in the kneader, the interaction of kneading elements induce a torque and force evolution on the shaft over one revolution.
Language: English / Year: 2006